New 2025 Realistic Free SolarWinds Hybrid-Cloud-Observability-Network-Monitoring Exam Dump Questions and Answer
Hybrid-Cloud-Observability-Network-Monitoring Practice Test Engine: Try These 152 Exam Questions
NEW QUESTION # 30
What is needed to edit trigger conditions in flow alerts?
- A. PowerShell
- B. SQL
- C. Python
- D. SWQL
Answer: D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
To edit trigger conditions for flow alerts in SolarWinds, the SolarWinds Query Language (SWQL) is required. SWQL is a proprietary subset of SQL designed specifically for the SolarWinds Orion Platform. The documentation specifies:
"Editing advanced alert trigger conditions and custom queries for flow-based alerts requires the use of SWQL, not PowerShell, Python, or standard SQL." References:
NPM Administrator Guide: Alerting and SWQL for Advanced Flow Alert Triggers
NEW QUESTION # 31
In which two of the following cases does duplicate flow data occur? (Choose two.)
- A. IP flow ingress on some interfaces and egress on others
- B. IP flow ingress applied on all interfaces, no egress usage
- C. both IP flow ingress and egress applied for all interfaces
- D. both IP flow ingress and egress applied on one interface
Answer: C,D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
Duplicate flow data typically results when both ingress and egress flow monitoring are applied simultaneously on interfaces. If both directions are enabled either globally (all interfaces) or locally (on a single interface), the same flow is counted twice-once entering and once leaving-resulting in duplicate statistics.
Reference:
"To avoid duplicate flow data, do not enable both ingress and egress NetFlow on the same interface or across all interfaces. Doing so will cause the same packets to be exported twice and counted as duplicates in reports and charts."
- (Network Performance Monitor Administrator Guide, NetFlow configuration best practices section)
NEW QUESTION # 32
Which two of the following tools are available for troubleshooting network node connectivity issues? (Choose two.)
- A. NetPath
- B. network insight
- C. asset inventory
- D. MIB browser
Answer: A,B
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
NetPath is specifically designed to trace and troubleshoot connectivity paths between nodes.
Network Insight provides in-depth analysis and diagnostics for specific vendors/devices, including health, connectivity, and configuration.
Asset inventory and MIB browser are not direct troubleshooting tools for connectivity.
Reference:
NPM Administrator Guide, "Troubleshooting with NetPath and Network Insight"
NEW QUESTION # 33
It is noted that the hardware health monitoring for a Cisco switch is generating false positives. It is verified that the alerted hardware issues are not occurring. What is causing the issue?
- A. MIB on the device is not the preferred MIB that is being polled.
- B. Restart SNMP on the device to refresh the hardware statistics.
- C. Modify the widget thresholds to filter out the false positives.
- D. Hardware sensors were incorrectly assigned to another switch.
Answer: A
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
False positives in hardware health alerts often occur when the polled MIB on the device is not the preferred or correct MIB for that particular hardware platform. This can result in SolarWinds interpreting SNMP data incorrectly, causing inaccurate alerts. Ensuring that the device is using the recommended MIB for hardware health resolves these false alert issues.
Reference:
"False hardware health alerts may result from polling the incorrect or non-preferred MIB on the device.
Always verify that the correct MIB is being polled for accurate hardware monitoring."
- (Network Performance Monitor Administrator Guide, Hardware Health Monitoring section)
NEW QUESTION # 34
A node has been added to hybrid cloud observability and shows an "unknown" status until the data is polled.
The default interval for polling status is two minutes.
If the node stays in the "unknown" status longer than the polling interval, which three of the following steps can be performed to resolve the issue? (Choose three.)
- A. Verify a ping response for this node is received through the ICMP.
- B. Run SNMP walk on the appropriate node.
- C. Verify the appropriate polling method is set for this node.
- D. Ping device from assigned polling engine.
Answer: A,C,D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
If a node remains in "unknown" status:
A). Ping device from assigned polling engine: Verifies direct network connectivity from the poller to the node.
C). Verify the appropriate polling method is set for this node: Ensures SolarWinds uses the correct protocol (ICMP, SNMP, WMI, etc.) for monitoring.
D). Verify a ping response for this node is received through the ICMP: Confirms basic reachability and that the node is not blocking ping requests.
Running an SNMP walk (B) can help diagnose SNMP-specific issues but is not always directly relevant to a node simply being in "unknown" status unless SNMP is the configured polling method.
Reference:
NPM Administrator Guide, "Troubleshooting Node Status 'Unknown'"
NEW QUESTION # 35
Which three of the following actions are native log entry actions in SolarWinds Log Analyzer? (Choose three.)
- A. Send an email notification
- B. Add a tag to the log entry
- C. Continue rule processing but do not save
- D. Halt further rule processing for the log entry
Answer: B,C,D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
According to theSolarWinds Log Analyzer Administrator Guide (Version 2024.1), Log Analyzer provides several built-in or native log entry actions as part of its log-processing rules. The key native log entry actions include:
* Add a tag to the log entry: This action allows you to tag event logs for easier searching and filtering later.
* Continue rule processing but do not save: With this action, the log entry is not saved but rule processing continues.
* Halt further rule processing for the log entry: Selecting this action will immediately stop the processing of any more rules for the current log entry.
Sending an email notification is an alert action and not considered a native log entry action in the context of log processing rules.
Exact Extract from Official Guide:
"Key features in LA
* Apply tags to event logs
* Drop unwanted event logs in LA
* Filter and analyze event logs
* Filter and view event logs in live mode
* Filter entry details in LA
* Filter on log tags..."- (Log Analyzer Administrator Guide, Page 53-54) Additionally, the guide specifies underCreate custom log-processing rules in LAthat actions such as tagging, halting processing, and not saving are among the native processing actions.
References:
Log Analyzer Administrator Guide, Page 53-54
Section: Key features in LA
Section: Create custom log-processing rules in LA
NEW QUESTION # 36
What is the correct sequence of steps to create a device studio poller?
- A. Select the technology, specify the data source, save the poller, and assign the poller to node.
- B. Assign the poller to node, select the technology, specify the data source, and save the poller.
- C. Select the technology, assign the poller to node, specify the data source, and save the poller.
- D. Select the technology, specify the data source, assign the poller to node, and save the poller.
Answer: D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
The correct process for creating a poller in Device Studio is:
Select the technology
Specify the data source
Assign the poller to a node
Save the poller
Reference:
"To create a poller in Device Studio: select the technology, specify the data source (OIDs), assign to nodes, and save."
- (Network Performance Monitor Administrator Guide, Device Studio section)
NEW QUESTION # 37
Network wide node and interface changes were recently made to several fields including names and IP addresses on nodes, captions, and aliases for their interfaces. Those changes are not updated in the hybrid cloud observability web console, even if a new polling is forced.
What should be done to resolve the issue?
- A. Run a rediscovery on both nodes and interfaces to refresh the data.
- B. Manually update the changed information in each poller.
- C. Delete and re-add each of the nodes and their interfaces.
- D. Run a rediscovery on the node, which will also update the interfaces.
Answer: D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
A node rediscovery updates all node and interface information, including names, IP addresses, captions, and interface aliases. Running a rediscovery on the node ensures all related interface details are refreshed in the SolarWinds database and web console.
Reference:
"Running rediscovery on a node refreshes both the node's and its interfaces' properties, including names and IP addresses."
- (Network Performance Monitor Administrator Guide, Node Rediscovery section)QUESTION
NEW QUESTION # 38
Which three of the following switch port report errors can cause a duplex mismatch? (Choose three.)
- A. CRC
- B. are collision
- C. > 0.5% receive
- D. 100 MB full
Answer: A,B,C
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
Duplex mismatches often result in specific types of switch port errors. According to SolarWinds documentation, the most common indicators of a duplex mismatch include CRC errors (B), high receive error percentages (C), and collisions (D). These errors occur because one end of the link operates in full-duplex mode (no collisions expected), while the other operates in half-duplex (collisions possible), resulting in frame errors, dropped packets, and high CRC counts. The option "100 MB full" refers to a speed/duplex setting, not an error.
Reference:
Network Performance Monitor Administrator Guide, "Diagnosing Duplex Mismatches - Symptoms and Errors,"
"CRC errors, excessive receive errors, and collisions are strong indicators of a duplex mismatch on switch ports."
NEW QUESTION # 39
What network capacity planning method is suitable for important devices and connections?
- A. average calculation
- B. peak calculation
- C. forecast calculation
- D. default calculation
Answer: B
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
For critical devices and connections, peak calculation is the recommended capacity planning method. This approach uses the highest observed utilization values within a time period, ensuring that planning accounts for maximum network demand and helps avoid bottlenecks during traffic spikes. SolarWinds documentation advises using peak calculations for important links to ensure network reliability and performance.
Reference:
Network Performance Monitor Administrator Guide, "Capacity Planning Methods,"
"Peak calculation is best for important interfaces and connections to capture maximum usage periods."
NEW QUESTION # 40
What is the most efficient way to create a custom NetFlow view to access at a later time?
- A. Create the view from flow navigator and save to the menu bar.
- B. Create the view from charting and graphing in NetFlow settings.
- C. Create the view from NetFlow settings and save to menu bar.
- D. Create the view from flow navigator and click the submit button.
Answer: A
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
The flow navigator in SolarWinds NetFlow Traffic Analyzer allows users to filter and analyze flow data. For future access, you can save your custom view to the menu bar from the flow navigator, providing one-click access to your saved configurations.
The documentation states:
"To save a custom NetFlow analysis for future use, configure your view in the flow navigator, then select the option to save the view to the menu bar for easy retrieval." References:
NTA Administrator Guide: Flow Navigator - Saving and Recalling Custom Views
NEW QUESTION # 41
Which custom poller supports multiple object IDs (OIDs)?
- A. universal device poller (UDP)
- B. component monitor
- C. hardware health
- D. device studio
Answer: D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
Device Studio is designed to enable support for complex devices and can poll multiple OIDs as part of a single custom poller definition. While Universal Device Poller (UDP) is also used for custom SNMP polling, it is generally limited to a single OID per poller. Device Studio is intended for use cases that require combining and correlating multiple OIDs for richer, template-based device monitoring.
Reference:
"Device Studio allows users to create custom device pollers that support multiple OIDs, enabling sophisticated monitoring for non-standard devices. This surpasses the single OID limitation of the classic Universal Device Poller (UDP)."
- (NPM Administrator Guide, Device Studio section)
NEW QUESTION # 42
Which Cisco IOS feature is enabled to pinpoint an application causing slow network performance?
- A. SPAN
- B. IPSLA
- C. SNMP
- D. NetFlow
Answer: D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
NetFlow is the Cisco IOS feature designed for monitoring and analyzing network traffic to pinpoint specific applications or endpoints consuming bandwidth or causing network slowness. It captures detailed flow information, including source/destination, ports, and protocols.
Reference:
NTA Administrator Guide, "Using NetFlow to Identify Traffic Sources and Applications"
NEW QUESTION # 43
From which two of the following locations can the status of the flow collector service be checked? (Choose two.)
- A. NetFlow collector services
- B. flow and CBQoS sources
- C. top XX receivers
- D. NetFlow settinqs
Answer: A,D
NEW QUESTION # 44
In live mode, how frequently is log viewer data automatically refreshed?
- A. 10 minutes
- B. 1 minute
- C. 10 seconds
- D. 1 second
Answer: C
NEW QUESTION # 45
A NetPath probe is to be built to monitor the paths between two sites. No Windows servers are available to run the agent. Which two of the following options can be used to set up the probe? (Choose two.)
- A. Run the probe from the hybrid cloud observability (HCO) server.
- B. Install the agent on a Red Hat Linux server.
- C. Install the agent on a Windows 10 computer.
- D. Use the network device agent to run the probe from the router.
Answer: A,C
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
NetPath probes require a supported Windows environment for deployment. According to the SolarWinds documentation, probes can be run from the Hybrid Cloud Observability (HCO) server itself, which must be a Windows server, or from any Windows client computer, including Windows 10. NetPath agents are not available for Linux or for network devices such as routers; the agent cannot be installed on Red Hat Linux or routers.
Reference:
Network Performance Monitor Administrator Guide, "Deploying NetPath Probes," NetPath Requirements: "NetPath probes can only be deployed on Windows computers or servers running supported Windows operating systems."
NEW QUESTION # 46
A router has been added for health and performance monitoring in hybrid cloud observability, however default SNMP polling data is not visible. Additional network devices have been added and SNMP metrics for those devices are now visible.
How should this issue be resolved?
- A. Perform an MIB database update to update the default
- B. Perform an MIB database update and build custom pollers to monitor the device.
- C. Perform an SNMP walk and add the devices MIB file to SolarWinds' MIB database.
- D. Perform a firmware upgrade on the device to update its MIB file.
Answer: C
NEW QUESTION # 47
Which two of the following locations can hardware health be enabled? (Choose two.)
- A. list resources
- B. main settings
- C. manage MIB
- D. asset inventory
Answer: A,D
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
Hardware health monitoring can be enabled during node discovery or after a node is added via the "List Resources" option. Additionally, hardware health can be enabled or viewed in the Asset Inventory page for nodes that support it.
From the documentation:
"You can enable hardware health sensors by selecting the option during resource discovery (List Resources) or later via Asset Inventory for individual nodes." References:
NPM Administrator Guide: Enabling Hardware Health
NEW QUESTION # 48
Which two of the following technologies are used when building device studio pollers? (Choose two.)
- A. CPU and memory load of single processor
- B. VLAN and VRF on a dedicated widget
- C. power supply status for vital statistics view
- D. machine type for node details widget
Answer: C,D
NEW QUESTION # 49
How does data collection with a flow collector differ from data collection with a polling engine?
- A. flow data is processed by flow collector or polling engine
- B. source devices must be configured to send their data to a flow collector
- C. flow data is collected by flow collector and processed by polling engine
- D. flow collector is a type of polling engine for flow data
Answer: B
NEW QUESTION # 50
In which two of the following cases does duplicate flow data occur? (Choose two.)
- A. IP flow ingress on some interfaces and egress on others
- B. IP flow ingress applied on all interfaces, no egress usage
- C. both IP flow ingress and egress applied for all interfaces
- D. both IP flow ingress and egress applied on one interface
Answer: C,D
NEW QUESTION # 51
NetPath can be used to diagnose a slow connection caused by an internal network. Details shown on the dashboard will be needed to help diagnose the problem. Which three of the following data points should be considered as possible causes? (Choose three.)
- A. Detailed alert description shown on NetPath.
- B. Latency and packet loss information.
- C. IP addresses of the nodes in question.
- D. Date, time, and duration of performance issue.
Answer: B,C,D
NEW QUESTION # 52
......
Guaranteed Success in SolarWinds Certified Professional Hybrid-Cloud-Observability-Network-Monitoring Exam Dumps: https://pass4sure.troytecdumps.com/Hybrid-Cloud-Observability-Network-Monitoring-troytec-exam-dumps.html